S1OF2 – One of two analog signals selector

Block SymbolLicensing group: ADVANCED
PIC

Function Description
The S1OF2 block assesses the validity of two input signals u1 and u2 separately. The validation method is equal to the method used in the SAI block. If the signal u1 (or u2) is marked invalid, the output E1 (or E2) is set to on and the error code is sent to the iE1 (or iE2) output. The S1OF2 block also evaluates the difference between the two input signals. The internal flag D is set to on if the differences |u1u2| in the last nd samples exceed the given limit, which is given by the following inequation

|u1u2| > pdevvmaxvmin 100 ,

where vmin and vmax are the minimal and maximal limits of the inputs u1 and u2 and pdev is the allowed percentage difference with respect to the overall range of the input signals. The value of the output y depends on the validity of the input signals (flags E1 and E2) and the internal difference flag D as follows:

(i) If E1 = off and E2 = off and D = off
, then the output y depends on the mode parameter:
y = u1+u2 2 , for mode = 1, min(u1,u2), for mode = 2, max(u1,u2), for mode = 3,

and the output E is set to off unless set to on earlier.

(ii) If E1 = off and E2 = off and D = on
, then y = sv and E = on.
(iii) If E1 = on and E2 = off (E1 = off and E2 = on)
, then y = u2 (y = u1) and the output E is set to off unless set to on earlier.
(iv) If E1 = on and E2 = on
, then y = sv and E = on.

The input R resets the inner error flags FlF4 (see the SAI block) and the D flag. For the input R set permanently to on, the invalidity indicator E1 (E2) is set to on for only one cycle period whenever some invalidity condition is fulfilled. On the other hand, for R= 0, the output E1 (E2) is set to on and remains true until the reset (Roff on). A similar rule holds for the E output. For the input R set permanently to on, the E output is set to on for only one cycle period whenever a rising edge occurs in the internal D flag (D = off on). On the other hand, for R = 0, the output E is set to on and remains true until the reset (rising edge Roff on). The output W is set to on only in the (iii) or (iv) cases, i.e. at least one input signal is invalid.

Inputs

u1

First analog input of the block

Double (F64)

u2

Second analog input of the block

Double (F64)

sv

Substitute value for an error case, i.e. E = on

Double (F64)

HF1

Hardware error flag for signal u1

Bool

off ..

The input module of the signal works normally

on ...

Hardware error of the input module occurred

HF2

Hardware error flag for signal u2

Bool

off ..

The input module of the signal works normally

on ...

Hardware error of the input module occurred

R

Reset inner error flags of the input signals u1 and u2

Bool

Outputs

y

Analog output of the block

Double (F64)

E

Output signal invalidity indicator

Bool

off ..

Signal is valid

on ...

Signal is invalid

E1

Invalidity indicator for input u1

Bool

off ..

Signal is valid

on ...

Signal is invalid, y = u2

E2

Invalidity indicator for input u2

Bool

off ..

Signal is valid

on ...

Signal is invalid, y = u1

iE1

Reason of input u1 invalidity

Long (I32)

0 ....

Signal valid

1 ....

Signal out of range

2 ....

Signal varies too little

3 ....

Signal varies too little and signal out of range

4 ....

Signal varies too much

5 ....

Signal varies too much and signal out of range

6 ....

Signal varies too much and too little

7 ....

Signal varies too much and too little and signal out of range

8 ....

Hardware error

iE2

Reason of input u2 invalidity, see the iE1 output

Long (I32)

W

Warning flag (invalid input signal)

Bool

off ..

Both input signals u1 and u2 are valid

on ...

At least one of the input signals is invalid

Parameters

nb

Number of samples which are not included in the validity assessment of the signals u1 and u2 after initialization of the block  10

Long (I32)

nc

Number of samples for invariability testing (see the SAI block, condition F2)  10

Long (I32)

nbits

Number of A/D converter bits (source of the signals u1 and u2)  12

Long (I32)

nr

Number of samples for variability testing (see the SAI block, condition F3)  10

Long (I32)

prate

Maximum allowed percentage change of the input u1 (u2) within the last nr samples (with respect to the overall range of the input signals vmaxvmin, see the SAI block)  10.0

Double (F64)

nv

Number of samples for out-of-range testing (see the SAI block, condition F4)  1

Long (I32)

vmin

Lower limit for the input signals u1 and u2  -1.0

Double (F64)

vmax

Upper limit for the input signals u1 and u2  1.0

Double (F64)

nd

Number of samples for deviation testing (inner flag D; D is always off for nd = 0)  5

Long (I32)

pdev

Maximum allowed percentage deviation of the inputs u1 and u2 with respect to the overall range of the input signals vmaxvmin  10.0

Double (F64)

mode

Defines how to compute the output signal y when both input signals are valid (E1 = off, E2 = off and D = off)  1

Long (I32)

1 ....

Average, y = u1+u2 2

2 ....

Minimum, y = min(u1,u2)

3 ....

Maximum, y = max(u1,u2)

2020 © REX Controls s.r.o., www.rexygen.com